Going the extra mile

  • Shipment on new orders for VHF/UHF amplifiers is now December, HF-1K January 2019, PowAbeam antennas 3-4 weeks.

Gemini HF-1K Solid State 1kW HF amplifier

 

  • 472kHz to 50MHz all bands
  • 1kW Minimum Output 1.8-50MHz
  • Fully automatic Band switching
  • High Spectral Purity
  • Silent full break-in QSK
  • Touch Screen Full Colour LCD Display
  • Remote operation via network interface
  • Three antenna outputs selectable by band
  • 0dBm SMA predistortion output
  • Advanced cooling
  • All aluminium main chassis
  • DUAL NXP BLF188XR LDMOS with Full Protection
  • 100-260V 50-60Hz power input
  • Dimensions 380w x 390d x 230h mm
  • Weight 19Kg
 

Availability: In stock

Price excl VAT: £2,083.33 Incl VAT: £2,500.00
 

Gemini HF-1K Front panel view

  • Gemini HF-1K Rear panel view
  • Gemini HF-1K typical front panel display
  • Gemini HF-1K band and antenna selection screen
  • Remote Software example screenshot

QUIET, EFFICIENT, AUTOMATIC, USER FRIENDLY.

CURRENTLY ORDERS NOW BEING TAKEN FOR JANUARY 2019 DELIVERY. You can secure an order with a 10% deposit. The balance will be payable in full prior to despatch. Please email us for more details.

The Gemini HF-1K is a solid-state 1kW 1.8MHz – 50MHz power amplifier with additional capability at 472kHz. It uses a PAIR of dual-LDMOS BLF188XR power devices for reliability, and has full high speed QSK capability using a diode switching circuit.

The thermal design is very conservative with a large heatsink, and OFHC heatspreader. This, assisted by several fans and a sophisticated thermal management system, allowing the channel temperature of the LDMOS device  to remain within limits which should ensure extended life, even with with heavy usage.

A major objective of the RF design has been to significantly exceed the spurious signal generation requirements of the international approvals standard (ETS 300 783 pts 1 and 2)  for amateur radio equipment. To this end the Gemini HF-1K has more extensive filtering than is usual in HF PAs.

While LDMOS power FETs are amongst the most rugged RF power amplifier devices currently available, they are sensitive to RF overdrive. The Gemini HF-1K has both extensive monitoring to minimise the risk of damage by overdrive and a conservatively designed input circuit.

The Gemini HF-1K employs full touch-screen control using a 480 x 272 pixel 108mm mm full colour TFT display. A wide range of monitoring functions are displayed, including power output, PA drain current, VSWR, band and antenna in use and heatsink temperature

As with other Linear Amp UK designs, there is no provision for ALC, as this is a major cause of bad signals.

Band selection is fullly automatic - no CAT needed. The presence of valid in-band signals is detected and will initiate switching automatically to that band. The amplifier will not transmit if out of band,

A high-speed, very low distortion, solid-state switching circuit will allows silent fast full break-in operation (QSK) to over 50wpm.

A single input and three selectable antenna output connectors are provided. The latter can be preset on a band by band basis.

A rear panel 0dBm SMA output is provided to allow connection to transmitters with linearisation capabilities. This  is 0dBm at 100w output or 10dBm at 1kW output and is optimised as a predistortion low level ouput for Anan and other SDR transceivers. It can, of course, be used for any other time of low level signal monitoring applications such as spectrum analysis.

The Gemini HF-1K has full network capability allowing remote operation and future firmware upgrades.

The amplifier is built in a very robust all aluminium case. A  modular assembly approach has been adopted with non-RF and high current DC interconnects being distributed as a single bus.

Outline specification.

Operating frequencies:                 460 – 479kHz*

                                                            1.8 – 2.0MHz

                                                            3.5 – 4MHz

                                                            5.0 – 5.5MHz

                                                            7.0 – 7.3MHz

                                                            10.1 – 10.2MHz

                                                            14.0 – 14.4MHz

                                                            18.0 – 18.2MHz

                                                            21.0  - 21.5MHz

                                                            24.8 – 25.0MHz

                                                            28.0 – 29.7MHz

                                                            50.0 – 54.0MHz

*when used with an external accessory low pass filter unit (not supplied)

 

Power output:                                     >1 kW at 1dB gain compression (200W+ on 460-479kHz)

Power input:                                        5, 10W, 50W, customer specified (50W supplied as standard)

3rd order IMD distortion:                    better than -30dB at 1kW

11th order IMD distortion:                       better than -70dB at 1kW

Harmonic suppression:                        better than 70dB (all harmonic products)

Input VSWR:                                              better than 1.5:1

Load VSWR tolerance:                      <1.5:1 for best performance with  2.5:1 high VSWR trip.

Operating Manuals, Remote Software and Firmware updates are available from http://linearamp.co.uk/ghf_software.html

* Required Fields

Price excl VAT: £2,083.33 Incl VAT: £2,500.00